無線網對刀儀對刀精密度0.01mm；
合適于維宏組織體制、美國simens、德國三菱機床系統、法那科、澳門寶元、新代、華北機床特點組織體制
一. 利用 Application
低輸出功率有線對刀儀,適用性于以及CNC加工制作中央.
low-power wireless tool setting gaguge, applications operating in all kinds of machine cnc center.
.jpg)
二． 支配根據方法步驟表明 Operation Instruction
1．將軍受器毗連到體系中，下例聲明函：（領受器）
Connect the receiver to the cnc system
.jpg)
領受器旌旗燈號聲明函The receiver pin configuration :
.jpg)
申明：description
1、Prob為外觀繼物品錄入的1個腳，守則卑微Prob發生閃斷境況，當對刀暈人的未時，Prob合閉。
Prob is the electric relay output normal open switch,which will be closed when the probe signal is triggered.
2、給領受器配電：領受器撐持5V到24V的電流電壓填寫。
當領受器有電壓降進入后，領受器起頭責任，領受器的責任唆使燈閃灼。
Power on the receiver.please make sure that the input power is 5v-24v DC. The work led flash to indicate power on ok.
3、給對刀器系統設計上2節AAA電瓶。
折開對刀器底蓋------儀器上2節AAA微型蓄電池組（重視起來微型蓄電池組 -標地需求）------裝上對刀器底蓋
Install the two AAA batteries to the terminal device.
Open the the battery door->install the 2 AAA.(Attention to The battery positive and negative direction )->close the battery door.
.jpg)
4、輕壓下對刀儀，對刀唆使燈亮；互相遠程數字毗連唆使燈亮；對刀儀將對刀旌旗燈號遠程數字處理決定給領受器，領受器對刀唆使燈亮，對刀開關按鈕占據倒圓角狀況發生；達到對刀。
To Touch the bulge of the tool setting gauge device until the probe led and the RF Led light. the probe signal will be transferred to the receiver,the receiver will trigger the probe switch to close.
三、電器叁數 Electrical specifications
3．1：領受器（The receiver）
．目標任務電流：撐持寬電流搜索：整流：5V到24V
Work voltage:5v~24DC
．級任務直流電：飽滿直流電乘以：20Ma
Current consumption: type 20ma
．wlan回收利用距離：20米
Wireless distance:20 meter
．內部繼電子元件電路圖產品發送：撐持250V/50mA額定負載;常開型;對刀閃避,繼電子元件電路圖產品收縮.
The relay normal open contacts output: support maximum 250V/50ma load.
3．2：對刀器（The tool setting gauge）
．重任相電壓：2節AAA電池箱，直流電源2.4V到3.6V
Work voltage:2 AAA batteries,2.4V~3.6V DC
．任務卡直流電壓：均直流電壓高于20uA；2節AAA電池充電能通常情況下使用6六個月
Current consumption: type 20uA.To work continuously more than 6 months
．無線網絡利用率隔：20米
Wireless distance:20 meter
．對刀反復性切確度：0.01公分
Probe precision:0.01mm
直流電正告：當對刀器蓄電池板電阻降到2.4V，大家改換蓄電池板。
Low power warning:please exchange the batteries when low power led light
｜English｜
.jpg)